3.8 KiB
Quick Deployment
The instructions, configuration files and scripts referred to in this section can all be found in the peach-config repo.
Prerequisite Steps
Download the latest Debian Buster preview image for RPi3 and flash it to an SD card.
Note: Be sure to use the correct device location in the dd command, otherwise you risk wiping another connected USB device. sudo dmesg | tail can be run after plugging in the SD card to determine the correct device location:
wget https://raspi.debian.net/verified/20200831_raspi_3.img.xz
xzcat 20200831_raspi_3.img.xz | sudo dd of=/dev/mmcblk0 bs=64k oflag=dsync status=progress
On Mac OS, use the following command to flash the SD card:
xzcat 20200831_raspi_3.img.xz | sudo dd of=/dev/sdcarddisc
Alternatively, use Etcher.
Note: if the above image link stops working, you can find the complete list of Raspberry Pi Debian images here.
Setup
Quick setup commands to connect to a local WiFi network over the wlan0 interface (assuming eth0 connection is not possible):
# username
root
# password (by default raspberry debian requires no password, so we set the password for root here)
passwd
# set interface up (run command twice if you receive 'link is not ready' error on first try)
ip link set wlan0 up
# append ssid and password for wifi access point
wpa_passphrase <SSID> <PASS> > /etc/wpa_supplicant/wpa_supplicant.conf
# open wpa_supplicant.conf
nano /etc/wpa_supplicant/wpa_supplicant.conf
[ Add the following two lines to top of file ]
ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=wpactrl-user
update_config=1
[ Save and exit ]
# open network interfaces config
nano /etc/network/interfaces
[ Add the following lines to the file ]
auto lo
iface lo inet loopback
allow-hotplug wlan0
auto wlan0
iface wlan0 inet dhcp
wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf
[ Save and exit ]
reboot now
[ Pi should now be connected to the WiFi network ]
Scripts
The setup_dev_env.py script can be executed once your Pi is internet-connected and git and python have been installed.
apt update
apt install git python
git clone https://github.com/peachcloud/peach-config.git
cd peach-config
# run the script with --i2c and --rtc flags to configure
python scripts/setup_dev_env.py -i -r ds3231 <USER>
Running the script with the -h flag shows the help menu:
usage: setup_dev_env.py [-h] [-i] [-r {ds1307,ds3231}] user
positional arguments:
user username for the default user account
optional arguments:
-h, --help show this help message and exit
-i, --i2c configure i2c
-r {ds1307,ds3231}, --rtc {ds1307,ds3231}
configure real-time clock
A <USER> argument must be supplied to create a new system user. You will be prompted to enter a password for your newly created user.
The script also allows optional configuration of I2C and real-time clock (RTC) modules. I2C configuration is necessary for the OLED display and physical interface to work correctly. RTC configuration is required for the real-time clock to work correctly. When passing the -r flag, the type of real-time clock module must be included (either ds1307 or ds3231). Selecting real-time clock configuration will not work if the I2C flag is not selected (in other words, the real-time clock requires I2C).
Run the script as follows for a full installation and configuration with I2C and the ds3231 RTC module (username in this case is peach):
python scripts/setup_dev_env.py -i -r ds3231 peach